1766 UM001 EN P PDF

Publication UMA-EN-P – November Table of Contents . User Manual UM to assign an IP address to the MicroLogix. controller. Publication INC-EN-P – October Important . Manual UM .. publication UM, for more information on surge suppression. rm_-en-p – Free ebook download as PDF File .pdf), Text File .txt) or read book online for free. Document Number IN UM

Author: Mezizuru Douhn
Country: Senegal
Language: English (Spanish)
Genre: Art
Published (Last): 25 September 2018
Pages: 336
PDF File Size: 9.36 Mb
ePub File Size: 7.36 Mb
ISBN: 111-9-49046-690-8
Downloads: 61177
Price: Free* [*Free Regsitration Required]
Uploader: Kazilkree

Rockwell Automation

It must be mounted within an enclosure that is suitably designed for those specific environmental conditions that will be present and appropriately designed to prevent personal injury resulting from accessibility to live parts. Do not drill holes above a mounted controller if the protective debris strips have been removed.

Make sure that the placement of the controller on the DIN rail meets the recommended spacing requirements see Controller Spacing on page 12 for more information.

Locate your controller as far as possible from power lines, load lines, and other sources of electrical noise such as hard-contact switches, relays, and ac motor drives. Make sure that the MicroLogix system is properly grounded. Install your controller using these installation instructions. Plug the ribbon cable connector into the bus connector. For more information, contact your local distributor or Rockwell Automation representative, or visit http: This equipment is supplied as open-type equipment.

  KVB LINIENNETZ PDF

Combinations of equipment in your system are subject to investigation by the local Authority Having Jurisdiction at the time of installation. A flat-blade screwdriver is required for removal of the controller. Leave the protective debris strip attached until you are finished wiring the controller and any other devices.

1766-IN001 – Rockwell Automation

Because of the many variables and requirements associated with any particular installation, Rockwell Automation, Inc. By using suppression, you also reduce the effects of voltage transients caused by interrupting the current to that inductive device, um00 prevent electrical noise from radiating into system wiring.

The Belden cable has two signal wires black and clearone drain wire, and a foil shield. Run the ground connection from the ground screw of the controller to the ground bus prior to connecting any devices.

United ; Contact your distributor.

Finger-safe cover TIP If you wire the terminal block with the finger-safe cover removed, you may 1676 be able to put it back on the terminal block if the wires are in the way. Use a static-safe workstation, if available. Each product is supplied with markings on the rating nameplate indicating the hazardous location temperature code. MicroLogix Instruction Set Reference Manual RM A reference manual that contains data and function files, instruction set, and troubleshooting information for MicroLogix The controller can be mounted to ENx7.

Use AWG 14 wire. Communication pins used for RS communications are alternately used for 24V power on the other MicroLogix controllers.

IN – Rockwell Automation

Power Loss in Transmission Lines. This means that either the battery wire connector is disconnected, or the battery may fail within 2 days if it is connected. Installation Assistance If you experience a problem within the first 24 hours of installation, please review the information that’s contained in this manual.

  CDX-R3300 MANUAL PDF

Store the equipment in appropriate static-safe packaging when not in use. Wiring category 1 2 – on signal ports 2 – on power ports 3 – on communications ports Terminal screw torque 0. For Safety information on the handling of lithium batteries, including handling and disposal of leaking batteries, see Guidelines for Handling Lithium Batteries, publication AG Trademarks not belonging to Rockwell Automation are property of their respective companies.

If you would like a manual, you can: This could cause an explosion in hazardous location installations. Follow these steps to install your controller using mounting screws.

Place a flat-blade screwdriver in the DIN rail latch at the bottom of the controller. You must provide a Customer Support case number call the phone number above to obtain one to your distributor in order to complete the return process.

Additional noise immunity can be obtained by routing the cables in grounded conduit.