ASTM D3276 07 PDF

Designation: D – 07Standard Guide for Painting Inspectors (Metal Substrates)1 This. Buy ASTM D GUIDE FOR PAINTING INSPECTORS (METAL SUBSTRATES) from SAI Global. ASTM D – Designation: D – 00 Standard Guide for Painting Inspectors (Metal Substrates.

Author: Zulut Mezikinos
Country: Mexico
Language: English (Spanish)
Genre: Sex
Published (Last): 5 March 2008
Pages: 367
PDF File Size: 10.9 Mb
ePub File Size: 1.32 Mb
ISBN: 479-5-81199-237-5
Downloads: 83958
Price: Free* [*Free Regsitration Required]
Uploader: Talabar

The angularity sharpness and density of the pro? Material Safety Data Sheets needed to ensure that personnel take necessary precautions in handling asstm materials. The part to be cleaned is placed in the saturated vapor above the heated solvent so that the solvent vapor condenses on the metal surface. Sstm necessary to remove grime and oil substances, they can be wiped, steam cleaned, power washed with detergents or cleaned with solvents selected so as not to soften the?

Originally published as D — Visible moisture Safety on the Job: If uncorrected, dry spray may create holidays, leading to poor performance, and it can interfere with adhesion of the applied or subsequent coat.

Heavy winds result in considerable loss of coating and excessive drying of the droplets reaching the surface. The weight-per-gallon cup holds a given 3d276 when?

Current edition approved June 10, Product MSD sheets 3. Note 1 – For additional helpful information, refer to the following documents: Poor spray technique resulting in excessive overspray a sand-like? All dust, dirt, oil, grease, moisture, soot, tar, or other contaminants should be removed from unpainted surfaces.

The cleaning of each section, bay, or part of the work should be entirely completed, inspected, and accepted before any coating is applied. Occupational Health and Safety Administration regulations should be followed. Test the compressed air supply in qstm with Test Method D Surfaces that have been dry blasted should be brushed with clean brushes, blown with compressed air free of oil and moisture, or vacuum cleaned to eliminate any traces of blast products, dust, or dirt from the surface.


Record coatings batch numbers mixing procedure 9. Any stained surface will need to be restored to its original condition without damage to that surface. The contaminants should be removed not simply spread out by a thorough wiping of the affected areas with cloths saturated with clean solvent.

ASTM D – 07 Standard Guide for Painting Inspectors (Metal Substrates)

The tape is measured in the? Vapor degreasing does not remove astn matter, so parts should be wiped to remove any insoluble soils. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of atsm rights, are entirely their own responsibility.

This is particularly important with spot-blast cleaning. Many factors are important in ensuring proper application of coatings. High humidity can also affect the cure of some coatings. After drying, the crevices and cracks can be?

If it is felt that the skins are thick enough to have a practical effect on the composition, the remaining paint should not be used until it has been tested and found to be satisfactory. The solvent is applied to the surface by wiping or scrubbing with rags or brushes. Dip-type viscosity cup Test Method D 3. Washing may also be necessary between coats of paint. Read more about subscriptions. Recycled abrasive test 4.

Inorganic zinc-rich primers and moisture-cure urethanes require certain minimum humidity conditions for proper cure. Blasting debris that accumulates on horizontal surfaces should be removed. Holiday testing is performed before? Details of the many steps involved in proper coatings application should be recorded Section 4. Often it is acceptable in fabricating shops, but because of the possibility of damaging surrounding property or coating?


The voltage used is usually 3. Correct coating and mixing procedure 9. The minimum and maximum particle size of the abrasive may be speci? The different instruments that can be used are described in this section. When the existing coating contains regulated heavy metals such as lead or chromium, or other regulated compounds such as organotin, special precautions and handling of debris may be necessary.

ASTM D3276:15

Relative Humidity and Dew Point. The coating should then be cross-rolled to? Thus, an oil-based coating may take 2 to 3 days to harden sufficiently to be overcoated with d3267 coating of the same type. Lead pigmented primers should never be used over aluminum surfaces.

ASTM D – 15e1 Standard Guide for Painting Inspectors (Metal Substrates)

Recoat Times observed Chloride from deicing salts or a marine environment, and sulfate contamination from air pollution have been recognized as main factors in premature breakdown of existing coating systems. A web subscription provides an easy and secure access to ashm, and you are guaranteed to always have the latest edition.

C Pictorial Standard Sa 2 shows mill scale and con? For additional helpful information, refer to the following documents: High voltage holiday detectors are capable of producing various voltage outputs.