ILS-CON. ILS™ Control Center. USER MANUAL. Page 2. ILS-CON User Manual. 2 Legend™ R. DMX-. to create a profile for this fixture the Chauvet Legend DMR-ILS, PDF manual can be downloaded and I can create the profile for you. Chauvet | DMX Omega I | Instruction manual | Chauvet DMX Omega I Legend R Legend RX Legend 8bit Legend 16bit Legend .
|Published (Last):||14 August 2011|
|PDF File Size:||16.58 Mb|
|ePub File Size:||15.65 Mb|
|Price:||Free* [*Free Regsitration Required]|
The view is actviated by pressing the UDK. If the fixture data in the programmer is then recorded into a cue or UDK, the desk will record the palette reference number rather than the actual parameter values.
As the default patch of the ORB series takes up 96 or dimmer channels, it may be desirable to first delete the default patch. Adjusting any of the effect parameters using the control wheels is reflected in the Effects Window.
The lock code PIN is a four mqnual number — What is a fixture? This behaviour mimics that of an external mouse. The output value is shown corresponding control wheel.
Chauvet Moving Head: Stage Lighting & Effects | eBay
Using Desktop 1 and 2 will show the outputs cchauvet the two VGA connectors on the back of the console, assuming these have been left as Desktop 1 and 2. The THRU key is used for selecting a range of items. Direction This modifier determines which order the steps cues are output when the chase is run: To convert a playback into a submaster on ORB: Rotating the iPad will rescale the monitor window as required.
Intimidator Spot le Note – This function only applies to UDKs which have been assigned to channel data or a cue. The fixture number is the number you will refer to the fixture as within the desk software. These palettes are labelled with the stock colour names as supplied by the manufacturer. When you play back a cue, park a channel, or manually manipulate a channel in the programmer, you give ownership of the channel to that specific area of the desk.
Default Times This button determines what happens to mmanual parameter fade and delay times after the specified data has been recorded.
Output Window — Source View When the [Source] option is selected, the Output Window displays the source of the output data rather than the actual output values as follows: The Load Show Window is Select the required show from the list of available shows displayed.
Monitor Display 2 Enabled – Yes or No. The MAC fixtures will be renumbered, etc. Page 93 Programming Moving Groups If you need to re-order your groups, you can Move a group from one location to another.
Help to Create a Profile | ADJ Forums
To Move a macro from one location to another enter the command: The submaster will be copied together with any names, fade times and special settings. They appear in the schedule based on the alphabetical sorting of manufacturer and fixture type and are distinguished by having a green background, for example: Pressing [Snapshot] again will return the data selection and attribute selection buttons to their previous states.
A palette is a programming tool which allows you to define the values required in a fixture or group of fixtures to create a particular affect on stage. Each of the cue stacks has a soft button in the window. To exit Setup from any of the various Setup options, close the screen that is currently displayed using the [Close] button in the top right hand corner of the screen.
Fixtures plugged into this universe must have a DMX address set on them in order for the desk to be able to control them. Page 47 Setup Editing Fixtures Edit Fixtures allows you to carry out various functions relating to the fixtures assigned to the desk, including: Fixture Parameter Fixture 1 Fixture 2 Fixture 3 Fixture 4 Fixture 5 Original Value 50 50 50 50 50 New Value 30 35 40 45 50 Change in Value -5 0 Fan V Mode When several fixtures are selected and a fixture parameter is adjusted using a control wheel, that parameter on each of the selected fixtures will increase or decrease by a different amount from their original values, depending on the fixture number.
When the Speed is set to zero, the chase runs according to the delay and fade times that are programmed into each step cue in the chase. This tracking backup option is ideal for show-critical scenarios where a backup solution must be provided.
Help to Create a Profile | ADJ Forums
The address indicates where the device is located and in combination with the Subnet Mask, indicates what the desk can see, and vice-versa. The desk will offer you a drop down menu listing all legennd storage devices detected on the USB ports. To output the next memory in the stack, simply press the GO button again.
The output value is shown on the LCD sceren above the wheel.
When the Update Options Window is displayed – the attribute selection bar initially shows red tagged for each attribute in which one or more parameters of that attribute are tagged in the programmer and grey none for those attributes where no parameters are tagged.
Page 22 The final step in the Patch Wizard is to assign a fixture number to the fixtures.
Note — Deleting Cues Since the ORB desk is a tracking based console, deleting a cue from a cue stack could possibly affect other cues in that stack. When the [Create Auto Palettes] option is confirmed the desk generates a number of colour, beamshape and position palettes for each moving fixture type in the fixture schedule and a number of standard effects palettes, as described below.
This can be particularly useful when creating position palettes see page After the initial press of the PAUSE key, subsequent presses will step backwards through the cue stack using the current cue fade times. In the case of a cue, you effectively load the cue into the programmer, modify it and update it.
Once finished the Comments column will show SC: Figure 69 – Update Options The palette you loaded will automatically be selected, so you just need to press OK to complete the edit. These can be used in one of three ways — The ORB series has two distinct channel types: MFFs can be switched by using the Fader Func. Once released from a previous page, the submasters become available on the new page.