Setpoint. Display. Chromalox® Heil Quaker Boulevard • Lavergne, Tennessee Telephone: • FAX: QuickInfo. The Chromalox 1/4 DIN Temperature and Process Controller is a low cost, high performance single loop controller that can be used for temperature, flow. Find great deals for Chromalox rr RR Temperature Controller. Shop with confidence on eBay!.
| Author: | Voodoozahn Faujinn |
| Country: | Egypt |
| Language: | English (Spanish) |
| Genre: | Life |
| Published (Last): | 11 June 2011 |
| Pages: | 217 |
| PDF File Size: | 4.87 Mb |
| ePub File Size: | 4.5 Mb |
| ISBN: | 513-9-97816-885-9 |
| Downloads: | 72763 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Fauzil |
These optional outputs are indicated by the following controller model numbers: Value and the lower display shows the setpoint. By pressing ‘print’ button you will print only current page. Loop Alarm Output Output 3, 4, or 5 will be activated if selected. The program consists of 16 intervals plus a standby interval. The CLP is not a substitute for safety shutdown devices such as flow switches or overtemperature monitors.
Chromalox 2104 Technical Manual
Loop-Powered Common Figure 8. Chromalox Technical Manual Page 9 Figure 2. Your shipping cost will be displayed in your shopping cart. The DTR output is always enabled when the power is on. On each PAGE you will find a specific set of related functions. It is 204 necessary to jumper terminals 8 and 9 on the instrument to complete a 2-wire hookup.
RS lines can be run over distances up to 50 feet. Wiring connections for the digital communications interface are made on terminals using shielded serial interface cable.
Table of Contents Add to my manuals Add.
Chromalox 2104-rr100 2104RR100 Temperature Controller
Don’t show me this message again. The controller then measures the time for the process variable to respond increase or decrease the process variable and compares the measured time to the Loop Timer value.
Page 45 Chromalox Technical Manual Page 85 until the meter reads 20mA or 5. This organization allows you to go directly to the parameter to be adjusted, without stepping through a long series of unrelated entries.
Got it, continue to print. Section 6 Alarms The controller can provide up to three alarm outputs using Output 3, 4 and 5. The has up to seven 7 hardware switches Switch located on the bottom of the controller.
Page 54 Operation cannot be reset until the process is out of the alarm chromalod. Don’t have an account?
Secure Online Ordering Delivery time: Page 11 When driving a contactor coil or other inductive load, an appropriately rated AC snubber circuit is recommended Chromalox Part. When driving a contactor coil or other inductive load, an appropriately rated AC snubber circuit is recommended Chromalox Part.
Page of Go. Page 62 Cchromalox a failure occurs in the control circuitry of the controller, the control output will be turned off and ERR3 will be displayed on the lower display. The A typically ships in 1 working day or less plus allow additional time for your selected UPS or FedEx shipping method. Installation Temperature extremes and excessive moisture can damage the instrument. Page 17 Figure 2.
Page 71 Chromalox Technical Manual This allows you to set the Page 51 Chromalox Technical Manual Page 60 Loop Timer value. Page 3 Dual Relay Output Wiring Operation cannot be reset until the process is out of the alarm condition.
Verify wiring and external Page 98 OFF, 0. Sensor maximum ranges are: With universal sensor inputs and front panel operator setup, one controller can be easily field configured for a wide variety of applications, and simply reconfigured as application needs change.
RS and RS provide multidrop network communications where up to controllers can communicate with a single computer at a distance of up to feet. Self Tuning with Fuzzy Logic: All Dimensions in Inches mm. Place the controller through the square panel cutout and replace the mounting clip.
CHROMALOX TECHNICAL MANUAL Pdf Download.
Page 5 Chromalox Technical Manual Page 37 Chromalox Technical Manual Seconds, Minutes, Hours 1 second to Make 3-wire RTD connections to terminals 7, 8 and 9 as shown in Figure 2. Digital Communications Hardware Setup RS can be used to connect a computer or modem to a single controller.
AC Neutral Load Figure 2.
High and Low Settings for each Alarm Output. Page 4 3-Wire mA, Vdc Transmitter Millimeters are shown in parentheses.