In this article we will show how to interface the FOX board to a Real Time Clock chip from Dallas/Maxim type DS through the I2C protocol. DS, DS Datasheet, DS Trickle Charge Timekeeping Chip, buy DS Photograph. DS Dallas Semiconductor IC. Real Time Clock – DS This is a VERY simple tutorial on how to use the DS Real Time Clock with an Arduino, or Versilino, board. I will walk you.

Author: Tojajinn Mauran
Country: Bosnia & Herzegovina
Language: English (Spanish)
Genre: Life
Published (Last): 4 May 2009
Pages: 436
PDF File Size: 1.34 Mb
ePub File Size: 6.38 Mb
ISBN: 549-9-98981-341-8
Downloads: 85434
Price: Free* [*Free Regsitration Required]
Uploader: Nikoshura

This line is bidirectional, so when ss1302 FOX needs to write data in the peripheral it drives the line, however when the FOX has to receive data from the peripheral, it sets its line in input mode. That buffer can be read in a single communication session, called a “burst” mode.

DS Datasheet(PDF) – Dallas Semiconductor

Terms of use of this documentation Terms and conditions Acme Systems srl provided this documentation “as is” without ds102 or guarantees of any kind. For the name of a month, this page contains many languages: You are strongly advised to use dalkas DSwhich is very reliable and accurate and needs only a battery to run the crystal is inside the DS Other schematics use two 22pF with the crystal. The lithium batteries cannot be recharged hence it is necessary to block the DS chip in its recharge battery function.

The most used name is “3-wire interface”.

In case of sharing please indicate the origin: We not provide any direct support for the Open Source software which can running on our board but, through these pages and forum posts, we provide all of the information required to obtain the sources, install, use and update the Open Source software available on Internet.

Terms of use of this documentation. To prevent that, the DS has a buffer to store the clock data. Related Hardware and Fs1302. The most used date and time functions for the Arduino: Acme Systems srl provided this documentation “as is” without warranty or guarantees of any kind. Dz1302 a byte is read, the addres is written first. The Year ‘0’ isand not or That is also wrong.



See the datasheet for full specifications and a circuit. You can also see, from the console messages that you can obtain issuing from a telnet session or from the console itself the command: To guarantee the best stability of the timing it is recommended to follow the hints dlalas in the datasheet of the DS chip in terms of correct positioning of the Hz quartz.

The code below contains basic interface functions for the DS This is a cheap module with the DS For more info pleae look at this Forum Post.

They dallaa don’t work very well. Sources for Electronic Parts. Please note that all of the software we talking about is Open Source so you have to check any license provided by the software authors before using it in any commercial or non-commercial product, by yourself.

The data in this ram will get lost if the Arduino is off, and the battery or supercap gets empty. To prevent it we posed the pull-up resistor of Ohms. That would result in bad clock data.

PCS Charge Timekeeping IC DALLAS/MAXIM SOP-8N DSZ DSZ+ DS DS | eBay

In the proposed circuit as an application example, we used a common lithum battery type CR At this moment there is no official library for date and time functions for the Arduino. In particular for the Dallas DS RTC chip the support is already enabled in the memory image released with the FOX board, sowhen you connect the chip as explained in the following, it will be immediately used by the operating system without any software adaptation or script changing. This article is obsolete or related to a discontinued product.


So the code has to detect that condition to prevent an extra clock pulse. The Year data of the DS is only two digits The three pins for the interface should avoid to use the internal pull-up resistors of the Arduino. It has a Leap-Year compensation from up to for a value of Some schematics on the internet have pull-up resistors on the three interface lines.

Add a Dallas DS1302 I2C Real Time Clock

Board Setup and Configuration. Use it with Arduino 1. A crystal of Arduino on other Chips. The page at maxim for the DS with all information and datasheet: This circuit has pull-down resistors which are an extra, in many cases they are not needed.

The Vcc1 is for a battery or a rechargable battery or a supercap. That way the check for the 7th bit is not needed, since dallae line is always released. Infact, with the DS you could change the lithium battery with a rechargeable battery or a supercap if you want, and the chip has the capaility to recharge it when the main power supply is switched on. The standard date and time functions like: The playground is a publicly-editable wiki about Ds13302. The shipping office is closed from 21 dec up to 7 jan The chip has 31 bytes of ram.

I was noted that the code could be improved. To avoid the current flow towards the battery we interposed a series diode D1 and the limiting current resistor R1 of Ohms in such a way that the current can flow from the battery to the RTC and not on the other way.