HT12E ENCODER DATASHEET PDF

HT12E Encoder IC can be used only with its pair HT12D. These two ICs together form an Encoder and Decoder pair. Fri, 12 Oct GMT ht12e encoder ic ht12e datasheet pdf – HT12E is an encoder integrated circuit of. 2 12 series of encoders. They are. HT12E is a series encoder IC (Integrated Circuit) for remote control applications. It is commonly used for radio frequency (RF) applications. By using the.

Author: Vit Malashicage
Country: Uzbekistan
Language: English (Spanish)
Genre: Career
Published (Last): 16 June 2015
Pages: 494
PDF File Size: 3.71 Mb
ePub File Size: 4.91 Mb
ISBN: 189-7-18493-708-9
Downloads: 67851
Price: Free* [*Free Regsitration Required]
Uploader: Duran

Arduino based GPS receiver. We should set the bits in same pattern on Encoder and Decoder IC to pair them.

Interface GPS with Arduino. The Encoded 12 bit output data can be obtained from this pin. HT12E begins a 4-word transmission cycle upon receipt hr12e a transmission enable. This oscillator can be used by connecting these two pins through a 1M Resistor. The IC has a built in oscillator.

In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. This cycle is repeated as long as TE is kept datasheett.

Choosing Battery for Robots. Skip to main content. It encodes the 12 bit parallel data into serial for transmission through an RF transmitter. HT12E is an encoder integrated circuit of 2 12 series of encoders.

So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. Choosing Motor For Robots. For decoding a data the IC will requires an oscillator, luckily this IC has one in-built. This pin has to be connected to Ground 0V to enable the Transmission.

  6ES7 222-1BF30-0XB0 PDF

HT12E Datasheet

SPI Module of Arduino. It is mainly used in interfacing RF and infrared circuits.

The IC is has a wide range of operating voltage from 2. The primary function of HT12E daatsheet to encode a bit and send it out through the output pin. HT12E has a transmission enable pin which is active low. This high-density System-in-Package SiP integrates controller, power switches, and support components. It is very important that your Decoder should also have this same address for them to talk to each other. These are the 8-bit address bits, which is used to protect your data.

Virgin Galactic — Commercial Space Flight. These two ICs together form an Encoder and Decoder pair. Can range from 2. These four pins are used to send data, the data encoded here will be decoded on HT12D IC sharing the same address bits. Submitted by admin on 30 October These 12 bits are divided into 8 address bits and 4 data bits.

Pull yt12e Transmission Enable pin pin 14 to ground to activate transmission. A basic connection diagram for the HT12E IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. The 4-bit data that has to be sent has to be given to the pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7.

You can know to set up the HT12D after this from here. In this image I have made all four data bits as zero lowwhen this is decoded we will get the same kind of bits on the output side of HT12D, similarly dncoder can make any changes on these 4-bits and they will be reflected on the output side of the HT12D decoder IC.

  GONA GANNA REDDY STORY IN TELUGU PDF

TL — Programmable Reference Voltage.

HT12E Encoder IC

This data should be sent to the HT12D for decoding, it can either be sent directly through a wire or by using a wireless medium like RF or IR. Transmission enable; active low. As soon as TE returns to high, the encoder output completes its final cycle and then stops. What is Web Browser.

So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. If you want security you can connect any of the 8 pins to 5V to make it high. Can be datasheeg in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc.

Interface SD Card with Arduino.

They can also be connected to switches to manually send and receive data. They are paired with 2 12 series of decoders for use in remote control system applications. Supply voltage; 5V 2. Encder put, HT12E converts the parallel inputs into serial output. The encoded bit can be obtained from the Dout pin pin Connected to the Ground of circuit.