IC HT12D PDF

HT12D is a series decoder IC for remote control applications manufactured by Holtek. It is commonly used for radio frequency (RF) applications. Download. RF transmitter and RF receiver of Mhz; 3 push buttons; IC HT12D; IC HT12E; Hearders (male or female it doesn’t care); 3 resistors with a value from ( to. HT12D is a decoder integrated circuit that belongs to series of decoders. This series of decoders are mainly used for remote control system applications, like.

Author: Meztishura Dorr
Country: Jordan
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 8 December 2005
Pages: 95
PDF File Size: 11.95 Mb
ePub File Size: 12.33 Mb
ISBN: 494-6-31368-360-4
Downloads: 45662
Price: Free* [*Free Regsitration Required]
Uploader: Kagat

Virgin Galactic — Commercial Space Flight. In simple terms, HT12D converts the serial input into parallel outputs.

This pin will go high when a data is received. The IC has a built in oscillator. In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

Interface GPS with Arduino.

How IC HT12D works?

SPI Module of Arduino. Choosing Motor For Robots.

Hr12d series of decoders are mainly used for remote control system applications, like burglar alarm, car door controller, security system etc. Interface SD Card with Arduino.

Choosing Battery for Robots.

The input data code is decoded when no error or unmatched codes are found. HT12D is capable of decoding 12 bits, of which 8 are address bits and 4 are data bits.

  LUIS HUMBERTO CROSTHWAITE PDF

The Encoded 12 bit output data obtained from HT12E has to be given here. So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data.

To know how a 4-bit data can be encoded and then send id the input pin of this IC, we have to understand the working of the HT12E Encoder IC which is given here. What is Web Browser. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this Id pair will be best suited for you. This oscillator can be used by connecting these two pins through a 1M Resistor 17 Valid Transmission VT This pin will go high when a data is received.

Connected to the Ground of circuit. Supply voltage; 5V 2. For decoding a data the IC will requires an oscillatorluckily iv IC has one in-built.

It is mainly provided to interface RF and infrared circuits. It is very important that your Decoder should have the same address of that of the encoder.

How IC HT12D works? | JAY Robotics’s Blog

These are the 8-bit address bits, which is used to protect your data. It is not mandatory to use it. The 4-bit data that is received can be obtained on pins AD0 ht1d AD1 and an address of 8-bit has to be set using the pins A0 to A7. Submitted by admin on 27 October HT12D is a decoder integrated circuit that belongs to 2 12 series of decoders. They can also be connected to LED to physically view the received data.

  LC125A DATASHEET PDF

The hr12d on 4 bit latch type output pins remain unchanged until new is received. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc.

HT12D Decoder IC

If you want security you can connect any of the 8 pins to 5V to make it high. If any valid data is received they can be obtained from these four pins. This high-density System-in-Package SiP integrates controller, power switches, and support components. Skip to main content. The serial input data is compared with the local addresses three times continuously. A basic circuit diagram for the HT12D IC is shown below In the ht12s circuit I have set the 8-bit address data as 0b, by ht122d all address pins to ground.

We should set the bits in same pattern on Encoder and Decoder IC to pair them.